User Tools

Site Tools


reloop_beatmix_4

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
reloop_beatmix_4 [2016/08/20 10:23]
sblaisot [SysEx Messages]
reloop_beatmix_4 [2017/11/04 16:01]
sblaisot [Effects Section]
Line 132: Line 132:
  
 The effect section let you control the first two EffectUnits. There are two different effect modes mapped: The effect section let you control the first two EffectUnits. There are two different effect modes mapped:
-  * Single ​Effect mode (the default), where you can load a single effect ​in the EffectUnit and control the first 6 parameters +  * Multi Effect mode (the default), where you can load up to three effects ​in each EffectUnit and control ​then with the superKnob 
-  * Multi Effect mode, where you can load up to three effects ​in each EffectUnit and control ​then with the superKnob+  * Single ​Effect mode, where you can load a single effect ​in the EffectUnit and control the first 6 parameters
  
-|        ^ Single ​Effect mode ^ Multi Effect mode ^ +|        ^ Multi Effect mode ^ Single ​Effect mode ^ 
-^ FX1    ​| Effect parameter 1 | Turn left to disable effect 1 | +^ FX1    | Turn left to disable effect ​1 | Effect parameter ​1 | 
-^ FX2    ​| Effect parameter 2 | Turn left to disable effect 2 | +^ FX2    | Turn left to disable effect ​2 | Effect parameter ​2 | 
-^ FX3    ​| Effect parameter 3 | Turn left to disable effect 3 | +^ FX3    | Turn left to disable effect ​3 | Effect parameter ​3 | 
-^ Shift + FX1 | Effect parameter 4 | select effect 1 | +^ Shift + FX1 | select effect 1 | Effect parameter 4 
-^ Shift + FX2 | Effect parameter 5 | select effect 2 | +^ Shift + FX2 | select effect 2 | Effect parameter 5 
-^ Shift + FX3 | Effect parameter 6 | select effect 3 | +^ Shift + FX3 | select effect 3 | Effect parameter 6 
-^ Beats turn | dry/wet knob | SuperKnob ​|+^ Beats turn | SuperKnob ​| dry/wet knob |
 ^ Beats push |  EffectUnit enable/​disable ​ || ^ Beats push |  EffectUnit enable/​disable ​ ||
-^ Shift + Beats turn | Select Effect Chain | dry/wet knob |+^ Shift + Beats turn | dry/wet knob | Select Effect Chain |
 ^ Shift + Beats push |  Eject Effect Chain  || ^ Shift + Beats push |  Eject Effect Chain  ||
  
Line 232: Line 232:
  
 The "​Serato Identity Request"​ SysEx messages forces the controller to send the status of all controls on the controller surface. It is used in the init function of the mapping to match the Mixxx controls to the controller ones. This SysEx Message is built upon: The "​Serato Identity Request"​ SysEx messages forces the controller to send the status of all controls on the controller surface. It is used in the init function of the mapping to match the Mixxx controls to the controller ones. This SysEx Message is built upon:
-  * F0 :=> Begin SysEx Message+  * F0 => Begin SysEx Message
   * 00 20 7F => it's the Serato Manufacturer according to https://​www.midi.org/​specifications/​item/​manufacturer-id-numbers   * 00 20 7F => it's the Serato Manufacturer according to https://​www.midi.org/​specifications/​item/​manufacturer-id-numbers
   * 03 01 => The Serato'​s proprietary message   * 03 01 => The Serato'​s proprietary message
   * F7 => End of SysEx Message   * F7 => End of SysEx Message
reloop_beatmix_4.txt · Last modified: 2017/11/04 16:01 by sblaisot