This mapping features full 4-deck support and seamless integration of external devices.
Defines the speedup-factor used when using the searchbutton and scrolling.
Time in seconds before the end of the track in which the controller should warn you.
Timeinterval for the triangular Leds in ms
Percent how much the value changes with each encoder tick
The Hotcuepage should be reset to 1 when a new Track is loaded into the Deck
range: true or false
If [SHIFT]+[CUE] should trigger a reverse_roll
range: true or false
An array of rateRanges in percent
The Deck consists of the jogwheel, play, cue, the topContainer (which hold the eight square buttons and the four encoders), pitchslider, pitchrange, search, keylock, tap, sync and pitchbend ±.
The mapping features some peculiar features which might not be discoverable by standard trial-and-error.
A shift button is bound to its Deck, which means that you can't use the shift button of Deck1 to access a shifted function on any of the other three Decks. Moreover the shiftbuttons can also work as toggle switches instead of pushbuttons (enabled via components.js Button.type.powerWindow). This means that if the shiftbutton is pressed for a longer period than 275ms it will bounce back to its original state (like a regular shift-/pushbutton). If the Button was pressed for a shorter period than 275ms, the button will remain in that state until it is pressed again (like a toggling button).
The four lower buttons of the topContainer are hotcues. They can be changed by using the corresponding Encoder [HOTCUE PAGE]. The current assignment will then be shown for one second in the upper row. Currently up to 4 Pages are supported (with 4 hotcues each). A demo of how this looks can be seen on JsFiddle (not done yet) (the slider represents the Encoder).
Most of these controls behave as expected but they are listed in detail for the sake of completeness anyways.
Default: Starts regular Play.
Shifted: Plays Track in reverse.
Default: Standard Cue.
Shifted: reverse roll if shift is enabled (plays in reverse end enables slip) otherwise standard cue.
Default: Change rate temporarily.
Shifted: Change rate temporarily small.
Default: Momentary BPM Sync
Shifted: Toggles magnet (quantize)
Default: Tap the desired BPM of the Channel
Note: This functionality is broken until #1811 gets merged
Default: Enable Scratching (otherwise it just works just like moving the Jog without the platter)
Shifted: Speeds up platter movement for searching within the track
Default: Toggles track keylock
Shifted: Syncs Key
Default: Cycles Through pitchranges
Default: Normal Pitchslider (Down plays faster; can be changed in the global mixxx preferences)
The TopContainer holds four assignable Hotcue buttons, four loop buttons, which can enable FX via Shift, and four Encoderknobs.
Default: set/active Hotcue_X
Shift: clear Hotcue_X
visit special_features for more info on how these work
Default: Presses the Loop In button like in the UI
Shifted: Toggles EffectRack1
Default: Presses the Loop Out button like in the UI
Shifted: Toggles EffectRack2
Default: Creates a loop at the current position of current Loop Size.
Shifted: Toggles Slip
Default: De-/Re-activates the last loop
Shifted: Jumps to start of last loop and stops playback there
Default: Controls the Super Knob on EffectRack1.
Shifted: Controls the Mix Knob on EffectRack1.
Default: Controls the Super Knob on EffectRack2.
Shifted: Controls the Mix Knob on EffectRack2.
Default: visit special_features for more info on what this encoder does
Shifted: Double/Halve current Loop Size
Default: Jump in the direction turned
Shifted: Double/Halve current Beat Jump Size
The Mixer features four channels with identical functionality and controls for the library and other miscellaneous features.
A channel consists of a volume fader, a gain knob, knobs for low,mid,high EQ a Loadbutton and a pflButton. These are internally still part of the Deck which is why the shiftbutton of Deck 1 won't work with the Loadbutton or gainknob of Deck2/3/4.
Default: Channel Volume
Default: Channel Pre-Fader-Listening
these work as usual on the N4: Clicking another one deselect all other.
Press multiple at the same Time to PFL multiple Channels
Default: EQ Low
Default: EQ Mid
Default: EQ High
Shifted: QuickEffect1 (Usually Filter)
Default: Load Track into Deck
Shifted: Eject Track from Deck
The Library is managed via the Library Encoder. Any shiftbutton can be used to access shift functionanly
Default: Move Library Cursor Vertically
Shifted: Move Focus between panes
sometimes the focus is stuck somewhere (eg when using the searchbox) and is only recoverable with user intervention via a pointing device.
Default: Open/Close Folder / Load Item into first available Deck (Context-dependent)
Shift: Maximize Library
The Crossfader and its assignment buttons are integrated seamlessly with Mixxx.
Function as expected: Mutes the corresponding Deck in Mixxx if set to Line.
Normal: Uses the crossfader parameters that were present when the mapping was loaded Scratch: Uses Scratch typical parameters for hard cuts
Doesn't manipulate the mixxx controls. Make sure the head gain is not zero and the mix is set to 100% PFL
make sure its high enough within mixxx
expected behavior but doesn't manipulate any mixxx controls.
This is probably due to your Mixxx version not being up-to-date or this mapping not being merged yet. You can download the mapping directly on GitHub.