6. Example Setups

This chapter presents some example hardware setups with instructions for how to configure Mixxx to work with them.

Siehe auch

6.1. Computer Only

The built-in audio interface on most computers comes with a single stereo line-out and a microphone input. This can be set up with Mixxx in two ways:

6.1.1. Practicing Mixing / Broadcasting

This setup can be used with a single audio output for speakers or headphones to practice DJing without investing in any equipment other than a computer and a set of speakers or headphones. With this configuration, use the Pre/Main Knob to switch back and forth between the Master mix and PFL signal. This setup cannot be used to play for a live audience because the Master mix is not sent to an audio interface output. However, it can be used by radio DJs who only need to send the Master mix to a broadcast audience.

  1. Einstellungen „‣ Sound-Hardware öffnen

  2. Wähle die Ausgabe Registerkarte

  3. From the Headphones drop-down menu, select your built-in audio interface, then Channels 1-2. Although this is labeled Headphones, you can also plug speakers into the output jack of your computer.

  4. Depending on your audio interface, you can specify a microphone

    1. Use your built-in microphone or connect a microphone to your computer

    2. Überprüfe, dass das Mikrofon von Deinem Betriebssystem erkannt wird

    3. Die :guilabel:‘Eingang‘-Registerkarte öffnen

    4. Wähle den vom Mikrofon verwendeten Eingang im Mikrofon Auswahlmenü

  5. Klicke auf :guilabel:‘Anwenden‘, um die Änderungen zu speichern.

6.1.2. Playing for an Audience

This setup allows for playing to an audience without headphone cueing.

Using Mixxx with your built-in sound card

Verwendung von Mixxx mit einer integrierten Soundkarte

  1. Einstellungen „‣ Sound-Hardware öffnen

  2. Wähle die Ausgabe Registerkarte

  3. From the Master drop-down menu, select your built-in audio interface, then Channels 1-2

  4. Depending on your audio interface, you can specify a microphone

    1. Use your built-in microphone or connect a microphone to your computer

    2. Überprüfe, dass das Mikrofon von Deinem Betriebssystem erkannt wird

    3. Die :guilabel:‘Eingang‘-Registerkarte öffnen

    4. Wähle den vom Mikrofon verwendeten Eingang im Mikrofon Auswahlmenü

  5. Klicke auf :guilabel:‘Anwenden‘, um die Änderungen zu speichern.

6.2. Laptop und Splitterkabel

The cheapest way to DJ and cue with headphones uses a stereo-to-mono DJ splitter cable (also known as a “Y cable”) plugged into the headphone jack of a laptop or other computer. This cable divides the stereo output from a single jack into two separate mono signals.

This setup allows you to start DJing without having to invest in expensive equipment. However, because the signals are in mono, you and your audience will not be able to enjoy music producers‘ positioning of sound in space (although many club PA systems are wired in mono anyway). Furthermore, audio interfaces built into computers are usually low quality and often pick up interference from other components of the computer.

Using a built-in audio interface and a stereo-to-mono splitter

  1. Einstellungen „‣ Sound-Hardware öffnen

  2. Wähle die Ausgabe Registerkarte

  3. Check that your headphones are plugged into the side of the cable with a headphones symbol and that the speakers are plugged into the side of the cable with a speaker symbol.

  4. From the Master drop-down menu, select your built-in audio interface, then Channel 1

  5. From the Headphones drop-down menu, select your built-in audio interface, then Channel 2

  6. Klicke auf :guilabel:‘Anwenden‘, um die Änderungen zu speichern.

Warnung

Most splitter cables, particularly those marketed as headphone splitter cables, output the same stereo signal to two headphone jacks and will not work for this DJ setup. Also, if you use a generic stereo-to-mono splitter adapter, you may only be able to hear out of one side of your speakers and headphones. DJ splitter cables allow you to hear the same mono signal on both sides of your headphones and speakers.

6.3. Laptop and External USB Audio Interface

Using Mixxx together with an external audio interface

Using Mixxx together with an external audio interface

Using two audio interfaces (built-in + external)

  1. Einstellungen „‣ Sound-Hardware öffnen

  2. Wähle die Ausgabe Registerkarte

  3. From the Master drop-down menu, select the external audio interface, then Channels 1-2

  4. From the Headphones drop-down menu, select the built-in audio interface, then Channels 1-2

Using an external multi-channel audio interface

  1. Einstellungen „‣ Sound-Hardware öffnen

  2. Wähle die Ausgabe Registerkarte

  3. From the Master drop-down menu, select the external audio interface, then Channels 1-2

  4. From the Headphones drop-down menu, select the external audio interface, then Channels 3-4

  5. Klicke auf :guilabel:‘Anwenden‘, um die Änderungen zu speichern.

6.4. Laptop und MIDI oder HID-Controller

Siehe auch

The Controller section of the DJ Hardware chapter has background information about controllers.

6.4.1. Controllers with an integrated audio interface

Many DJ controllers include an integrated multi-channel audio interface. A setup with this kind of controller may look like the diagram below:

Using Mixxx together with a DJ controller and integrated audio interface

Using Mixxx together with a DJ controller and integrated audio interface

Using a controller with an integrated multi-channel audio interface

  1. Einstellungen „‣ Sound-Hardware öffnen

  2. Wähle die Ausgabe Registerkarte

  3. From the Master drop-down menu, select your controller’s audio interface, then Channels 1-2

  4. From the Headphones drop-down menu, select your controller’s audio interface, then Channels 3-4

  5. Klicke auf :guilabel:‘Anwenden‘, um die Änderungen zu speichern.

6.4.2. Controllers without an integrated audio interface

Controllers without an integrated audio interface can be used together with a USB audio interface as depicted in the diagram below:

Using Mixxx together with a DJ controller and external audio interface

Using Mixxx together with a DJ controller and external audio interface

Using a controller without an integrated audio interface

  1. Einstellungen „‣ Sound-Hardware öffnen

  2. Wähle die Ausgabe Registerkarte

  3. From the Master drop-down menu, select the external audio interface, then Channels 1-2

  4. From the Headphones drop-down menu, select the built-in audio interface, then Channels 1-2

  5. Klicke auf :guilabel:‘Anwenden‘, um die Änderungen zu speichern.

6.5. Laptop, externe Hardware-Mixer und Vinyl-Steuerung

Using Mixxx together with turntables and external mixer

Mixxx gemeinsam mit Plattenspielern und externen Mixer verwenden

This setup allows DJs to use the techniques of DJing with vinyl record turntables combined with the portability and flexibility of a laptop computer. Instead of carrying crates of records or CDs, DJs can carry their entire music collection on their laptop. In addition to a laptop and headphones, this setup requires an audio interface with at least two pairs of stereo inputs and outputs as well as a pair of timecode records.

Siehe auch

Gehen Sie zum Kapitel Vinyl-Steuerung für ausführliche Informationen.